超聲波清洗機說明書英文版（ULTRASONIC CLEANER INSTRUCTION）
KQ系列超聲波清洗機說明書英文版ULTRASONIC CLEANER INSTRUCTION如下：
一、ultrasonic cleaner Summery（超聲波清洗機概述）
1. ultrasonic cleaner Cleaning Principle:（超聲波清洗原理）
the principe of ultrasonic cleaner is high-frequency oscillator- signal thoughouts energy convertor(Vibrator) to convert high-frequency machine-oscillator to disfuse into fluid, the high-frequency oscillator signal is produced by the generator of ultrasonic, the ultrasonic can produce a millions of small air bubble, the air bubble is formed and growed in negtive zone, and close increasingly in active zone, it just is so-called “cavitational efficiency”, the closing of all air bubbles can forms a southands of instantaneous high pressure of atmospheric pressure, continuously growing high pressure seems a thousands of small”explosion” to beat superfacial of matter, to clean all contaminents.
2. ultrasonic cleaner usage:（科強KQ超聲波清洗機用途）
KQ series ultrasonic cleaner is made of international advanced, skilled design of the circuit; the compernant is made of high quality part from abroad and home, those parts passed quality test; the last, it is finished by advanced manufacturing skills. KQ-series has a liable work,high efficiency,and stable input’s power. It is used in Glass Flask, Rubble stopple, the cleaning of filter net and paper; the dealing of metal and non-metal, electronic, optimistic, instrument’s cleaning, ornament, rare metal,or expensive metal’s cleaning as well as disk’s cleaning,etc.
二、 ultrasonic cleaner Technical Paramters:（超聲波清洗機技術(shù)參數(shù)）
1.Ultrasonic Power:2800W
2.Frequency:28KHZ
3.Timing Range：1-99H99M99S(digital, set freely)
4.Temperature Range：RT-80℃（digital，set freely）
5.Heating Power:3000W
6.Tank size：550（L）×300（W）×550（H）mm
7.Voltage:220V,50Hz
8. Total Power：5800W
三、ultrasonic cleaner work principle:（清洗機工作原理）
1. the circuit is composed of swicth as well as other electronic parts, to apart dynamic electricity to rectification circuit and control-signel circuit.
2. the rectification circuit is made of imported high quality rectification brige, to convert alternating currency to DC
3. the control-singel circuit can produce high-frequency control singel by intergrated circuit
4. the high-frequency oscillator is composed of big power mode and circuit, it can produce alternating currency of high frequency oscillator(ostillation).
5. the other is composed of inductance and output conducer to counteract reactance heft of ultrasonic energy convertor.
6. operation instruction:
A. ultrasonic function usage: push the switch to ON position, then the ultrasonic is working to finsih part cleaning(timer controls ultrasonic working time).
B. timer usage:
Timing range:0S-99.99H
The middle of the switch for seting time function, the adjustment of middle for H. M. S. H for Hour, M for Min, S for Second; as for other adjustment for 0—9, for instance: 12 S 22 for 12.22 Seconds, 30M55 for 30.55 mins, 99H99 for 99.99hours.
C. usage of heating and temperature-control
Put heating switch to ON , after servral seconds, the temperature-controller will display measured temperature and controlled temperature, the top is display measured temperature and the down is controlled temperature, it is heating when the measured temperature less than controlled temperature semulantiously “OUT” led lights on temperature-controller; it is stoped when measured temprature more than controlled temperature semulantiously “OUT”led not lighting.
To press”SET” Key—SP menu- pressing “up” or “down” to adjust temperature, re-press”SET” Key to exit after adjusted temperature.
7. the ultrasonic energy convertor is attached in stainless crust by imported special viscocity.
四．ultrasonic cleaner Work environment:（超聲波清洗機工作原理）
1.environment temperature: 10℃—30℃, cleaning fluid temp: 10℃—50℃
2.relevant huminity≤80%
3.astomspheric pressure: 86~106Kpa
4. the range of working time≤8Hr
五．ultrasonic cleaner Method and attention（超聲波清洗機使用方法和注意事項）
this machine must be operated according to following content:
1. Voltage for 220V, Power Voltage will be in between 220V+10% and 220V-10%, low voltage will cause relay couldn’t liable connection, high voltage will cause the demage of ultrasonic generator.
2. ultrasonic cleaning tank’s temperature for 40degree, prohibiting no-water operation in cleaning tank, or else it will demage mchine, attention!
3. the fun of ultrasonic generator is to provide heat elimination , so we should keep nomal operation and good intake of heat elimination
4. to put ultrasonic cleaner in dry place, non-corrosion’s environment, the temp is not exceeds 30 degree.
5. to draw out power when we dismantal machine.
六. ultrasonic cleaner maintenance and pretection()
ultrasonic cleaner will be inspected in time, one time per three monthes.
1. to clean durty on main machine
2. to inspect if it is nomal, or is it in noise? Is the screw firmed?
3. work instruction’s lamp is nomal?
4. some resistance is good?
5. the capacitance is nomal?
6. some inserts(parts) is nomal?
七、ultrasonic cleaner standard configuration：
A、 ultrasonic cleaner 1 unit
B、 Silencing Lid 1 unit
C、 stainless frame 1 unit
Free Spareparts:
D、450V470UF Electrosis Capacity 1 unit
E、KBPC5010 Rectifier 1 unit
F、225K Capacity 1 unit
G、100Ω Resistance 1 unit
九、ultrasonic cleaner Structure Drawing
1. Graphic Model
2.Crust picture
3. Surface Picture
4.inside’s structure picture
十、simple mal-function checking（超聲波清洗機檢修）
No jumping Convertor insulation strength= 0 convertor is bad
1，air switch ohmmeter
Control board insulation strength>5 control board is bad
Jumping Rectifier Take down chip of active or negtive Jumping Rectifier is bad
2，Air Switch Air Switch
Mode No jumping Mode is bad
一，
1， First relay pick-up, then second relay is not pick-up, control board is bad.
2， Air switch will jump when resistance is bad(one year for Warranty)
3， Air switch will jump when mode is bad.(Mode for one year)
Sparepart List:
|
No. |
Name |
Quantity |
Model |
Warranty |
|
a |
Power |
1 |
220V |
1 |
|
b |
Signal Board |
1 |
30V 10W |
1 |
|
c |
Double15V Transformer |
1 |
220V 10W |
1 |
|
e |
mode |
1 |
100DY-12H |
1 |
|
g |
Wind motor |
1 |
220V 75W |
1 |
|
h |
Inductance |
1 |
2800W |
1 |
|
i |
Transformer |
1 |
2800W |
1 |
|
D |
Electrosis Capacity |
2 |
450V470UF |
1 |
|
E |
Rectifier |
2 |
KBPC5010 |
1 |
|
F |
225K Capacity |
2 |
225K |
1 |
|
G |
Resistance |
2 |
100Ω |
1 |
新聞中心
